Welcome To Sunraj Ceramic

No.	Characteristics	Wall Tiles ISO 13006 / EN-14411 Group Bill	Sunraj Value
[A] Dimension & Surface Quality
1	Devation In Length & Width	±0.5%	±0.3%
2	Deviation In Thickness	±0.5%	±0.5%
3	Straightness Of Sides	±0.5%	±0.3%
4	Rectangularity	±0.6%	±0.5%
5	Surface Flatness	±0.5%	±0.3%
6	Surface Quality	Min 95% Of Tiles Should Be Free From Visible Defects	> 95%
[B] Physical Proerties
1	Water Absorption	20% > E > 10%	< 16%
2	Modulus of Rupture	> 150 Kg/cm2	> 180 Kg/cm2 avg
3	Scratch Hardness	Min 3 Mohs	> 3 Mohs
4	Crazing Resistance	1 Cucle	Passes 4 Cycles
[C] Chemical Properties
1	Staining Resistance	Min Class 2	Resistant
2	Household Chemicals	Min Class B	Resistant
3	Scratch Resistance	Min 3	Min 3
[D] Thermal Properties
1	Thermal Shock Resistance	10 Cycles	Resistance
2	Thermal Expansion	9 x 10^-6 -K^-1 -1 max	Conforms

Packing Detail
DIMENSION (MM)	THICKNESS	PIECES	SQ. MTR.	WEIGHT
375 X 250 MM	8 MM (APP.)	8	0.75	9.00 KG. (APP.)

NOTE : (1) Certain amount of size and shade is inherent in all ceramic products (2) Our conformity to the above standards is applicable only for premium quality. (3) Colour shown are as accurate as the limitations of the printing will allow. (4) prospective customers are advised a simple of the tile before ordering. (5) Every effort has been made to ensure the accuracy of the information given. However the company reserves the right to change the specification without prior notice. (6)Sometimes variations in shade or size being inherent to ceramic industry may occur. It is suggerted to check the tiles before purchase and laying as company does not accept responsibility once the tiles are laid.

TILES FIXING
	Wall REQUIREMENT The Wall Should be Strong, Float, Clean and Dry. If The Tiling has to be done on plywood. the surface of wall should be sealed. with 50% volume mixture of PVA and water.
	TILES LAYING First of all, apply the high quality ceramic on the wall and place first tile in the corner. Apply even pressure on the four corner od the tile to ensure sticking. Fill the area of wall that can be filled with the tile without cutting and leave it for at least 12 hours. fill the rest of area with the measures and cut tiles.
	APPLYING GROUT The grouting is done on the next day. Apply the grout diagonally between the tile using a sponge to fill the gaps between the tiles. Clean and wipe the surplus grout with a sponge.
	HOLE CUTTING To pass the pipe through the tile, the tile should be cut in a specific manner. Mark the position on the tile which the tile will occupy. Draw a straight line passing through the center of the circle, cut the tile on the drawn. Cut the semi circle on each of the half and when thes two halves are placed together it will form a hole.
	ACCESSORY TILE FITTING While laying the normal tiles, keep on empty space where an accessory tiles will be fitted. Apply the adhesive on the back of accessory tiles and apply even pressure to place the accessory tile.
	TILES PREPARATION Mix the tiles from different cartoon which will help in fine blending of shades.
	TAMPING PROCESS To ensure the proper contact of tiles with the wall, temp the tile with a rubber mallet evenly.
	CURVE CUTTING To fit the tiles in a curved surface of washbasin etc. measure and mark the curve in cardboard and place the cardboard on the tile before cutting it.
	WINDOW RECESS TILLING AND CUTTING Tile has to be cut in " L " shape for window recess. Cut a line from center to edge and than draw a right angle line vertical down. cut line to get on " L "shape that can fit in a window
	TILES DRILLING Apply masking tope to cover the area to be drilled. Mark the position of hole and drill the hole with lowest possible pressure on the drill.

Technical Specification: